The Jack's Small Engines Forum - Join Our Online Community
Reply to post

Hot!Husqvarna ST227P Drive Belt Spring

Author
KLDinPA
New Member
  • Total Posts : 3
  • Scores: 0
  • Reward points: 0
  • Joined: 2019/02/01 04:41:54
  • Status: offline
2019/02/01 04:50:15 (permalink)
0

Husqvarna ST227P Drive Belt Spring

While replacing the drive belt, a very small spring fell off. Unfortunately I forgot
to take a picture before taking the machine apart.
Part:  587031201
Can anyone show me where this very small spring belongs ?
 
Thanks...
 
kd
 

3 Replies Related Threads

    kshansen
    Super Member
    • Total Posts : 96
    • Scores: 0
    • Reward points: 0
    • Joined: 2015/12/04 10:48:29
    • Status: offline
    Re: Husqvarna ST227P Drive Belt Spring 2019/02/02 08:31:51 (permalink)
    0
    Not familiar with the Husqvarna machines but I took a look on Jack's and found the breakdown for the machine here:
    https://www.jackssmallengines.com/jacks-parts-lookup/manufacturer/husqvarna/snow-blowers-throwers/st-227p-96193009702-2015-05/drive
     
    Only springs I see are #9 and #10 not sure if that helps. Might take some looking but if you can figure out where they go at one end just see if there is some place to hook the other end.
     
    Looks like #10 might hook on to lever #28 at least at one end. Just noticed there are two of the #10 springs and they both seem to hook over similar levers at the opposite ends of a shaft!
     
    #9 appears to slide over spacer #4 and spacer #4 slides over the shaft on what they are calling bracket #8
     
    Hope I did not confuse you but that is the best I can do without seeing the spring you are talking about. Not sure if there is an easy way to post pictures to this forum short of posting them to a separate image site then posting a link here.
     
     
    KLDinPA
    New Member
    • Total Posts : 3
    • Scores: 0
    • Reward points: 0
    • Joined: 2019/02/01 04:41:54
    • Status: offline
    Re: Husqvarna ST227P Drive Belt Spring 2019/02/02 09:01:12 (permalink)
    0
    kshansen
    Not familiar with the Husqvarna machines but I took a look on Jack's and found the breakdown for the machine here:

     
    Only springs I see are #9 and #10 not sure if that helps. Might take some looking but if you can figure out where they go at one end just see if there is some place to hook the other end.
     
    Looks like #10 might hook on to lever #28 at least at one end. Just noticed there are two of the #10 springs and they both seem to hook over similar levers at the opposite ends of a shaft!
     
    #9 appears to slide over spacer #4 and spacer #4 slides over the shaft on what they are calling bracket #8
     
    Hope I did not confuse you but that is the best I can do without seeing the spring you are talking about. Not sure if there is an easy way to post pictures to this forum short of posting them to a separate image site then posting a link here.
     
     




    Spring I need a home for is #5   Thanks.

    Attached Image(s)

    kshansen
    Super Member
    • Total Posts : 96
    • Scores: 0
    • Reward points: 0
    • Joined: 2015/12/04 10:48:29
    • Status: offline
    Re: Husqvarna ST227P Drive Belt Spring 2019/02/02 13:38:56 (permalink)
    0
     
    KLDinPA
    Spring I need a home for is #5   Thanks.




    Sorry I missed that one! Had to zoom way in to even see it.
     
    Could it possibly fit in that notch in the top right side of #2 called a swing plate? Maybe there is something in the frame it hooks on?
     
    Hope someone familiar with the Husqvarna blower sees your message. I might be able to figure it out in person but not by texting, good luck!
    Jump to:
    Copyright © 1994 - 2016 Jacks Small Engine & Generator Service, LLC