The Jack's Small Engines Forum - Join Our Online Community
Jacks Small Engines Lawn Mower & Power Equipment Forums
Community Stats
1 day 7 days 30 days Max. View More
Top Posters
  1. SRTsFZ6
    (74 Recent Posts)
  2. rowingone
    (9 Recent Posts)
  3. GED
    (6 Recent Posts)
Most Active Threads
  1. Kipor 3000 ti with rod knock?
    (15 Replies)
  2. Poulan Pro High Wheel mower Chute problem !
    (9 Replies)
  3. ToroZX600 Spindle Pulley
    (7 Replies)
Top Rated Posts
  1. Re: Best Fuel Stabilizer?
    (+2)
  2. Re: Best Fuel Stabilizer?
    (+2)
Birthdays
There is no record available at this moment
2023/10/29 20:10:53
T_Rose_3825

Log splitter pull start stuck!

I have a B&S Quantum XE 6.0 ( engine # 123K02-0238-E1 04081157 ) Model # 24AF55CC729 427385 WITH SERIAL # 1H154H50023.

Ok, so I brought it down to split some wood and set it up, checked fluids and then started it. I let it run for say...2 mins....as I took a seat on a log to begin splitting, it started smoking! So I turned it off and checked it out. The oil dipstick was oiled from top to bottom. So I wiped it off and checked again and it was still all over the place.
Needless to say, I didn't split any wood yesterday. I just let it sit. I found this site last night after I looked up some B&S Q&A's and found this to be a better place to get answers.
Anyway, I went out this morning and pulled the plug. GROSS! I pulled the cord and it was good but black (oil?) came out of the hole? I wiped that all up and put new plug in and tried to pull to star and the pull cord is super hard to pull.....
Long story short.....my question is what do I do now?
7 comments Leave a comment
SRTsFZ6
Your carb is float/needle is leaking fuel into the intake manifold and eventually the crankcase / combustion chamber.
 
You need to drain all the oil and fluid from the combustion chamber. 
 
Pull the carb , check the needle and seat for crap keeping it from sealing..
 
.
 
 
2023/10/30 15:26:40
T_Rose_3825
0k, I got all your replies and I am working on it now. Everything looks good, other than it being dirty from normal wearing and of course the oil in the cylinder. Can I just blow out the cylinder with air? It won't disturb anything?
2023/10/30 16:17:50
SRTsFZ6
Just spin the engine over with the spark plug out..  You can spray some brake cleaner in there but it'll start with the spark plug clean and not fouled.  
 
It'll smoke a bunch on start up but will clear out once it kicks..
 
.
2023/10/30 16:22:16
T_Rose_3825
Ok, I did that. Just gas comes out now. I put spark plug back in and pulled. It still has some resistance and it wants to jerk it out of my hand. I still haven't gotten it to turn over yet. But at least I have some tug on the pull cord now.
2023/10/30 19:20:23
T_Rose_3825
Oh yeah, I pulled the spark after a few pulls and it's wet but not black....sooo....I will let it sit for a second and then try again.
2023/10/30 19:23:39
T_Rose_3825
Woohoo! It's running again! I still have residual smoke but it's running! I think I'm going to have to try and put a load on it now and see if I can get some wood split.

Thank you so very much. Your time and help is very much appreciated!
2023/10/30 20:16:28
SRTsFZ6
That's great!
 
You still need to address that carberator. 
 
At the very least check the oil level before use.   
 
 
.
 
 
 
 
2023/10/31 08:17:54

Comments are closed.

Copyright © 1994 - 2016 Jacks Small Engine & Generator Service, LLC
© 2025 APG vNext Trial Version 5.5