The Jack's Small Engines Forum - Join Our Online Community
Reply to post

Briggs and Stratton 18hp V-TWIN motor# 350777-1137-E1

Author
Post
Essentials Only Full Version
stony69jason
Starting Member
  • Total Posts : 12
  • Scores: 0
  • Reward points: 0
  • Joined: 2025/07/06 22:26:58
  • Status: offline
2025/07/07 00:05:17 (permalink)
0

Briggs and Stratton 18hp V-TWIN motor# 350777-1137-E1

This motor is on John Deere GT235 lawnmower motor# 350777-1137-E1.

I just bought it and this vacuum line wasn't hooked up, it's on front left side of carb (looking at it). Does anyone know where it goes ? Could you please tell me so I can hook it up properly. There is a second hole in the air filter backing plate just below the main PVC hole but its a little big for the vacuum line. I will include pictures. Thank you in advance.
post edited by stony69jason - 2025/07/07 19:16:04
Quote  #1

5 Replies Related Threads
    stony69jason
    Starting Member
    • Total Posts : 12
    • Scores: 0
    • Reward points: 0
    • Joined: 2025/07/06 22:26:58
    • Status: offline
    Re: Briggs and Stratton 18hp V-TWIN motor# 350777-1137-E1 2025/07/09 04:11:55 (permalink)
    0
    https://postimg.cc/MXd087Gr
    Quote  #2
    SRTsFZ6
    Super Member
    • Total Posts : 2365
    • Scores: 80
    • Reward points: 0
    • Joined: 2018/11/18 07:20:58
    • Status: offline
    Re: Briggs and Stratton 18hp V-TWIN motor# 350777-1137-E1 2025/07/09 06:30:27 (permalink)
    0
    I responded to your PM in regards to that vent line...
     
     
     
    post edited by SRTsFZ6 - 2025/07/09 06:31:30

    Scott
    Quote  #3
    SRTsFZ6
    Super Member
    • Total Posts : 2365
    • Scores: 80
    • Reward points: 0
    • Joined: 2018/11/18 07:20:58
    • Status: offline
    Re: Briggs and Stratton 18hp V-TWIN motor# 350777-1137-E1 2025/07/09 06:33:12 (permalink)
    0
    Also, new folks on the forum are often denied immediate ability to post pic's W/O 
    admin approval...
     
     
    .

    Scott
    Quote  #4
    stony69jason
    Starting Member
    • Total Posts : 12
    • Scores: 0
    • Reward points: 0
    • Joined: 2025/07/06 22:26:58
    • Status: offline
    Re: Briggs and Stratton 18hp V-TWIN motor# 350777-1137-E1 2025/07/09 07:05:43 (permalink)
    0
    Thank goodness the picture appeared. Does this vent go in the backside of the air filter housing?? There is a hole there
    Quote  #5
    SRTsFZ6
    Super Member
    • Total Posts : 2365
    • Scores: 80
    • Reward points: 0
    • Joined: 2018/11/18 07:20:58
    • Status: offline
    Re: Briggs and Stratton 18hp V-TWIN motor# 350777-1137-E1 2025/07/09 07:09:22 (permalink)
    0
    It's very possible as it's venting, you'd want it in a "protected / filtered"  area away from flying grass/dirt.
     
    Is the line about the same length to fit in that hole W/O mods? 
     
    Is the hole about the same size of the hose? (thought it was different).
     
    .

    Scott
    Quote  #6
    Jump to:
    Copyright © 1994 - 2016 Jacks Small Engine & Generator Service, LLC
    © 2025 APG vNext Trial Version 5.5