The Jack's Small Engines Forum - Join Our Online Community
Reply to post

Drive Belt Adjuster Spring on Z248F Zero Turn

Author
Post
Essentials Only Full Version
Conbert
New Member
  • Total Posts : 1
  • Scores: 0
  • Reward points: 0
  • Joined: 2022/05/23 17:43:46
  • Status: offline
2022/05/23 17:50:30 (permalink)
0

Drive Belt Adjuster Spring on Z248F Zero Turn

Replaced the drive belt pully with no problem except I can figure out where the spring attached to the mower.  Anybody give me a clue?  I get where it goes on the pully cut can't seem to find a hole for the spring on the frame.  Help!
Quote  #1

4 Replies Related Threads
    SRTsFZ6
    Super Member
    • Total Posts : 2096
    • Scores: 74
    • Reward points: 0
    • Joined: 2018/11/18 07:20:58
    • Status: offline
    Re: Drive Belt Adjuster Spring on Z248F Zero Turn 2022/05/23 18:13:36 (permalink)
    0
    Are you taliking about the hydro belt, part #5?  Or the blade belt? 
     
    https://www.jackssmallengines.com/jacks-parts-lookup/manufacturer/husqvarna/zero-turn-consumer/z-248f-967336701-2015-01/hydraulic-pump-motor 
     
    Quote  #2
    SRTsFZ6
    Super Member
    • Total Posts : 2096
    • Scores: 74
    • Reward points: 0
    • Joined: 2018/11/18 07:20:58
    • Status: offline
    Re: Drive Belt Adjuster Spring on Z248F Zero Turn 2022/05/23 18:14:00 (permalink)
    0
    .

    Attached Image(s)

    Quote  #3
    Randal61
    New Member
    • Total Posts : 1
    • Scores: 0
    • Reward points: 0
    • Joined: 2022/05/24 13:33:32
    • Status: offline
    Re: Drive Belt Adjuster Spring on Z248F Zero Turn 2022/05/24 13:39:26 (permalink)
    0
    Hi, I'm new here. I have a 2014 Murray 155-42.   I am trying to find a layout of the belt formation on the deck. I', needing to replace a belt for it, and I misplaced my manual, and I am having a hard time finding one on the internet, plus most Utube videos are not very informative, i believe they are just trying to get numbers. Any help would be greatly appreciated, thanks in advance.  Randal
    Quote  #4
    SRTsFZ6
    Super Member
    • Total Posts : 2096
    • Scores: 74
    • Reward points: 0
    • Joined: 2018/11/18 07:20:58
    • Status: offline
    Re: Drive Belt Adjuster Spring on Z248F Zero Turn 2022/05/24 17:42:40 (permalink)
    0
    Randal61
    Hi, I'm new here. I have a 2014 Murray 155-42.   I am trying to find a layout of the belt formation on the deck. I', needing to replace a belt for it, and I misplaced my manual, and I am having a hard time finding one on the internet, plus most Utube videos are not very informative, i believe they are just trying to get numbers. Any help would be greatly appreciated, thanks in advance.  Randal


     Here ya go:
     
    https://www.jackssmallengines.com/jacks-parts-lookup/manufacturer/cub-cadet/murray/13-lawn-tractors/2014-models/13am775s058-2014-m155-42-2014/mower-deck-42-inch 
     
    Around the outside two SPINDLES, then inside the two idlers, then up to the engine..
    Quote  #5
    Jump to:
    Copyright © 1994 - 2016 Jacks Small Engine & Generator Service, LLC
    © 2025 APG vNext Trial Version 5.5