The Jack's Small Engines Forum - Join Our Online Community
Jacks Small Engines Lawn Mower & Power Equipment Forums
Reply to post

intake to head gaskets

Author
Post
Essentials Only Full Version
longnkrnch
Starting Member
  • Total Posts : 10
  • Scores: 0
  • Reward points: 0
  • Joined: 2017/03/16 11:34:42
  • Status: offline
2017/03/23 11:58:06 (permalink)
0

intake to head gaskets

I have a Briggs 44l777 0115 b1 on a JD z425. When I pulled my carb, it only has what looks like a flat ring gasket in a recessed groove between the intake and the head. The parts diagram shows two gaskets one is a flange type gasket and the other is shown as a "seal o ring" can anyone tell me which of these I need to use or does it take both?
Thanks
Quote  #1

6 Replies Related Threads
    Mikel1
    Moderator
    • Total Posts : 1179
    • Scores: 41
    • Reward points: 1
    • Joined: 2016/04/14 18:48:53
    • Location: Georgia
    • Status: offline
    Re: intake to head gaskets 2017/03/23 13:35:28 (permalink)
    0
    Are you referring to part # 690949 & part # 691917?
    Quote  #2
    longnkrnch
    Starting Member
    • Total Posts : 10
    • Scores: 0
    • Reward points: 0
    • Joined: 2017/03/16 11:34:42
    • Status: offline
    Re: intake to head gaskets 2017/03/23 15:27:29 (permalink)
    0
    Yes, Mike. Those are the ones.
    Quote  #3
    Mikel1
    Moderator
    • Total Posts : 1179
    • Scores: 41
    • Reward points: 1
    • Joined: 2016/04/14 18:48:53
    • Location: Georgia
    • Status: offline
    Re: intake to head gaskets 2017/03/24 09:09:41 (permalink)
    0
    Ok, the seal o ring goes on the intake piping.
    So is the gasket you took off round, rubbery like the seal o ring?
    post edited by Mikel1 - 2017/03/24 09:10:50
    Quote  #4
    longnkrnch
    Starting Member
    • Total Posts : 10
    • Scores: 0
    • Reward points: 0
    • Joined: 2017/03/16 11:34:42
    • Status: offline
    Re: intake to head gaskets 2017/03/24 11:42:06 (permalink)
    0
    Yes, they seem to be rubber. Engine did not have the flange type gaskets. Do I also need those?
    Quote  #5
    Mikel1
    Moderator
    • Total Posts : 1179
    • Scores: 41
    • Reward points: 1
    • Joined: 2016/04/14 18:48:53
    • Location: Georgia
    • Status: offline
    Re: intake to head gaskets 2017/03/25 00:00:18 (permalink)
    0
    No, you do not need them. The seal o rings are for the plastic intake piping on the v twin.
    Quote  #6
    longnkrnch
    Starting Member
    • Total Posts : 10
    • Scores: 0
    • Reward points: 0
    • Joined: 2017/03/16 11:34:42
    • Status: offline
    Re: intake to head gaskets 2017/03/25 17:10:42 (permalink)
    0
    Thanks
    Quote  #7
    Jump to:
    Copyright © 1994 - 2016 Jacks Small Engine & Generator Service, LLC
    © 2025 APG vNext Trial Version 5.5