Craftsman Forum

Craftsman Forum
Post New Thread
Regular
migtoledo75

craftsman model# 917.271.022 Serial# 111698C019769 brake assembly looks incomplete

hello everyone, i recently picked up a free ride mower. I'm slowly trying to bring it back to life. iI took a look at the brake assembly to see what condition they were in and to me it looks like its missing pieces. I've seen youtube videos and those brakes have a circular i guess you would call a c..
4
2024/10/07 21:06:00
raski

Heavy Blowby

After getting this old Craftsman/Roper GT18 finally running, another issue could put a halt to this project. The engine is a B&S 18hp flat headed twin cylinder. Model number is 422437. Oil is being pushed out violently (with great force) from the two breather tubes into the air cleaner housing. ..
1
2024/07/11 08:58:15
[email protected]

Connect idler spring rod to deck

I have a craftsman T8200 riding mower with a 46-inch cut. I know the idler spring connects to the idler spring rod. Where do I connect the idler spring rod to the deck?..
4
2024/07/09 16:29:08
sonora108

One of a Kind?

I own a Craftsman T3000 that was built in 2018 model number 247.273300 and I have done many internet searches and haven't found a mower that is the same as this one. Shift lever on left side Forward, Neutral and Reverse. Mower deck controls on right side. Tractor is black and gray. My problem is the..
6
2024/07/09 08:15:05
Ronbo442

Reverse Override Switch

My Craftsman Pro 8200 will not cut in reverse. When you turn the ignition switch bach to the reverse override position and push the orange triangle button, the red light comes on but goes of by itself or just after pusging the reverse accelerator pedal. I think its in the ignition switch assembly an..

2024/05/24 12:57:47
muc

Craftsman DYT 4000 transaxle problem

M/N 917.273620Hydro Gear 314-0510 TransaxleLast year it started to lose speed in reverse, got to the point it would barely move. Did notice that if I pulled really hard on the motion control lever it would move a little faster. Forward seemed to be fine.Now this year it is losing forward, it can bar..

2024/05/20 10:27:32
pizzasplatter

Craftsman 917377690 lawnmower starts but then dies after primer fuel used up

I've tried all I can think of, but the mower always shuts down once the primer pumps of gas are used up.There's new gas in the tank.There's gas in the bowl of the carb and gas flows freely if I take the bowl plug out.I've taken the carb apart, cleaned it, and blown air through all the holes.Cleaned ..
5
2024/05/20 07:37:05
woundedbear

craftsman chainsaw 20" 54cc 3.3 ci cylinder removal

There are no bolts on the bottom of the saw. Looks like removal of cylinder is thru four screws on the base of the cylinder. Impossible to get to. body on this thing is all one piece nothing comes off. The screws are inset under the fins on the cylinder. I ground down three allen wrenches and manage..
1
2024/04/30 12:50:08
Dawgn86

Craftsman Drive Belt Pulleys

Good morning, Craftsman model 917-203900 / Serial # 021714A00317 lawn tractor. I am replacing the front two drive belt pulleys. I got one off and replaced but on the second one, the bolt unloosened some and now just the bolt and screw turns..cant unloosen it..cant tighten it back. On the diagram, ho..
2
2024/04/26 16:45:14
Yellamo

Sitting in Seat - Display stops working

So I'm having an issue getting the motor blades to engage. Recently replace the carberator and the engine runs smooth now but when I pull the blade switch, nothing, doesn't engage. But I did notice a strange thing. Not sure if it's related to the blades but now when I sit in the seat, the little lcd..
2
2024/04/22 11:53:06

1 2 - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account