Zero Turn Forum

Zero Turn Forum
Post New Thread
Regular
hemmjo

Bunton BZT 2190 Relay issue

My Bunton BZT 2190 has 3 relays in a block under the seat. A few years ago, after starting the engine, as soon as I release the parking break, the engine died. Unable to find a readable schematic, I began to trouble shoot by just trying things. I discovered that by removing the center of those 3 rel..

2025/06/05 14:00:13
jrgsmnn

Craftsman Zero Turn Muffler Replacement

Good morning. I have a Craftsman Zero Turn with a Kohler Z6000 engine and I'm trying to replace the muffler, but I can't get a tool in to remove and replace the bolts that hold the exhaust pipes to the engine. Does anyone have any tips I can use? Thank you...
3
2025/05/20 08:01:51
OldPoco

Electrical problem with Timecutter 42"

Hello All.My Toro 74360 serial 290011235 mower has a weird problem. I hugged a tree a little close on the left side at the rear wheel and the mower instantly died. After a couple of tries to restart it turned out the main 30 amp fuse was blown. After replacing it the mower would start and run but as..
4
2025/05/05 19:25:42
GreenMachine00

JD Z225 electrical/pto problems

I have a john deere z225 (2004). I have had problems before with the pto, so I replaced it (2011). Recently, I replaced the engine (1 week ago) with a new B&S EX1900. The engine runs perfectly and I have mowed with it in total approximately 1 hour. Yesterday roughly 30 min. into mowing, the mowe..
4
2025/04/29 17:09:33
cnc52

PTO SWITCH PROBLEM

I REPLACED THE DRIVE BELT ON A TORO #74412 ZERO TURN MOWER. NOW WHEN YOU START THE MOTOR THE PTO IS IN THE OFF POSITION AND THE BLADES ARE SPINNING. IF THE PTO SWITCH IS ENGAGED THE MOWER SHUTS DOWN. THIS OCCURRED WITH PARKING BRAKE ON BUT NO OCCUPANT IN THE SEAT. ANY HELP OR SUGGESTIONS WOULD BE AP..
1
2025/04/27 07:38:28
[email protected]

Dixon Ram Mag 50 dies when PTO engaged

2006 DixonDuring Trouble shootingPTO replaced 3 ohms, and 12 Volts, jumps to 14V while Tring to engage, right before engine dies.seat safety switch bypassed tied together for trouble shootingBrake Safety switch changes state during ohmcontrol arms safety switches change state during ohmPTO switch ch..

2025/04/27 07:32:08
TennBears

My Cub Cadet zero turn pto will not work

I am working on a buddys mower. It is a Cub Cadet zero turn, model ZT1-42, manufactured in 2019. Initally the problem was that the pto would not engage. I tested the pto switch and it was fine. I then unplugged and tested the seat switch and both control arm switches and then plugged them back up. T..
1
2025/04/24 08:34:44
TobiasBeacher

Hydro Gear ZT-3400

How do you remove the tube charge triple O ring Part#54501 from the aluminum housing inside. They are loose and they spin but I have no way to grab ahold of them to pull them out to finish the tear down of this pump. Any advice would help. Thanks in advance...
1
2025/04/12 06:53:16
granky

Toro Z5000 deck replacement

I have a 2008 Toro z5000 and the stamped mower deck has rusted out beyond repair. I have located a fabricated 50 inch deck from a newer Toro MX5050 in good condition about 200 miles away. From photos they look interchangeable and from what I can find out both use the same 1/2 x 141 inch belt. The MX..
3
2025/04/02 06:58:32
HJR

ZTH 4218 Model 968999167

My Husqvarna zero turn was built in 2002. It runs fine but the deck is very loud. I was told I need new spindles but they aren't available. Not being a mechanic, I was wondering if the bearings could be the issue and if so can they be replaced without damaging the spindles and would those bearings e..
1
2025/03/04 13:34:17

1 2 - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account