Briggs & Stratton Forum

Briggs & Stratton Forum (p.3)
Post New Thread
Regular
randyw57

Maintenance Parts for MTD 450 Chipper

I have a MTD 450 Chipper. B&S Horizontal Engine. 206 cc 8.5 ft. lbs of torque There is a series of number on the valve cover (it is OHV). They are: 070924 88 85 660 126312 0525 B8 I’m looking for information on routine maintenance. But I’d like to get some more specific information for my r..
5
2025/04/28 18:30:10
RedTex

Cam Compression confusion

I have a Toro Titan Z that quit starting unless I manually rotate the engine off compression and then it starts fine. Numerous YouTube videos led me to a broken camshaft compression release lever failure as a probable cause. The Toro site says I have a B&S 44K777-0123-E1 and to go to the B&S..
1
2025/04/27 07:06:43
Small Engine Repair

Briggs Intek 6.5 OHV Troubleshooting

I have a John Deere push mower with an early 2000s Briggs Intek OHV engine that I am fixing for a friend. the mower has spark, 60 PSI compression, clean carb, but still can't get it to even pop when starter fluid is sprayed through the plug hole. After that, I took the valve cover off, and everythin..
5
2025/04/13 14:14:36
dns0247

What should operating temperature of a Briggs 12 HP IC engine be?

..
1
2025/03/20 07:00:46
clkorschgen

Low Oil shutoff on Briggs 305447-0037-G1

Repowering a AMT 4" trash pump with a new B&S 305447-0037-G1. This new engine has an oil filter, and on top of the filter it looks like a sensor with a tab for an electrical connection. This is a bare tab, no wire attached. Is this part of a low oil shutoff system? If so, what kind of wiring wou..
1
2025/03/19 18:48:45
ueww40

Governor Adjustment for 20 HP B&S V2

I just replaced a blown governor on my 20 HP twin B&S engine and now I am in the process to adjust it and I am not quite sure how to understand the manual. My throttle is twofold. The first 80% of it is throttle and the last 20% of it pulls the choke. The manual says to turn the control swivel C..
18
2025/03/01 06:32:11
Harrison DM

17.5 Briggs and Stratton

set throttle cable and runs rich back tires through carb. Seems like the gov. Spring is weak. Is there a starting position for the throttle lever before I lock down the cable...
1
2025/02/25 17:49:59
Steverino

25HP Intek V-Twin OHV Top No Load RPM?

Model 445777 0264-E1 Code 051121YG Engine's on a JD 155C tractor. I've got the repair manual for this engine but not the Microfiche MS-6225 or Sales Manual MS-4052. Anyone know what the Top NL RPM should be? My "guess" would be around 3450-3550 RPM. (Not great at guessing) Thanks in advance!..
4
2025/02/18 11:54:31
76FX

Regarding checking oil.

I have an older Cub Cadet with a Briggs motor. My Briggs repair manual shows oil capacity to be 48 oz, but after 32, it shows full. This engine has a dipstick and I'm wondering what the proper way to check it is. Should the dipstick be screwed down, as if in normal operating position or should the l..
8
2025/02/08 13:24:22
PBM

Briggs 3HP horizontal shaft with Pulsa-Jet/Fixed Jet carburetor adjustment

Greetings Folks,I am working on a 3HP Briggs and Stratton horizontal shaft motor, #80232-2242-01. It has a Pulsa-Jet/Fixed-Jet carburetor on it. I thoroughly cleaned the carburetor and replaced the diaphragm on it and installed with new intake and gas tank gaskets. The motor starts and pretty well w..
3
2025/02/04 11:30:31

1 2 3 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account