Latest Posts

Latest Posts (p.10)
Kawasaki Engine Forum
robsallee

Re: FD851D Engine Map 1 and Map 2 switches

turns out the map 1 and 2 pins aren't even used on my engine - no wires in those pin slots..

2025/06/17 17:02:02
Locating Parts
SRTsFZ6

Re: B&S Powermate generator engine carburetor.

https://www.jackssmallengines.com/jacks-parts-lookup/manufacturer/briggs-stratton/briggs-stratton-engine/100000-19z999-series/115400-to-115499/115432-0081-01/carburetor Clean these jets super clean #'s 117 and 142. That should, (un-less you have a leaking needle and seat), fix your issue... ...

2025/06/17 13:46:01
Scag Forum
robsallee

Re: FD851D Engine Map 1 and Map 2 switches

...turns out after making my fancy diagram using the schematics, my mower doesn't actually even have all those wires on the old (existing) harness. I have only 4 wires...so still trying to match wires up (or run new ones, whatever the case may be). Any help would be appreciated...or at lest sympathy..

2025/06/17 13:35:53
Generator Forum
SRTsFZ6

Re: B&S Powermate generator engine carburetor.

Jets #142 and #17 ARE the critical jets that MUST be spotless and fully clear... ...

2025/06/17 13:33:54
SRTsFZ6

Re: B&S Powermate generator engine carburetor.

Cleaning, especially with an ultra sonic cleaner is WAY better than replacing with an after marketChinese piece of c..p.... One of my customers before and after pic with an ultra Sonic cleaner(NO manual cleaning): https://i.postimg.cc/nr9P5jDY/Before.jpg https://i.postimg.cc/90Tj9NJh/After-1.jpg..

2025/06/17 13:31:35
Kohler Engine Forum
homebrewz

KT-735-3076 Running Rich/Poorly Under Load

Greetings, I have a KT-735-3076 engine in a Troy-Bilt Super Bronco XP with 128 hours. When it stalled out after hitting something and wouldn't start, I made the mistake of jumping it with a running vehicle. I replaced the battery and starter. Fortunately, the voltage regulator was OK. However, it's ..
4
2025/06/19 18:19:09
Generator Forum
Conan

Re: B&S Powermate generator engine carburetor.

The carb p/n is in the listing for find number 125. You have to look in the second column and the p/n 715317 shows it is for type 0081. Thats how I determined what carb p/n I’m looking for a replacement for. I talked to a friend and he suggested disassembling the carb and running it through an ultra..

2025/06/17 11:06:51
Small Engine Forum
SRTsFZ6

Re: The mounting bolts shrank- Briggs mower carburetor reinstallment

Don't hammer on anything, period. Those threaded bolts are 1/4" x 20. There are threads inside the intake manifold where the carb bolts to, correct? As something definitly isn't right, get some "all thread, 1/4 x 20". You can measure and cut "longish" for now.. With the 2 new studs, thread them into..

2025/06/17 07:19:47
Jchaps20

Re: The mounting bolts shrank- Briggs mower carburetor reinstallment

Hyperlink for forum attempt 3 One hour hammer results with 80% bolt target depth 3in1 oil utilitzed with hammer to encourage flange/ridged grooves into manifold/intake Bolt holes. Bolts are about 1cm from the exit port on the opposite carb end. Bolts protrude about 1 inch from their poin..

2025/06/16 23:39:45
Jchaps20

Re: The mounting bolts shrank- Briggs mower carburetor reinstallment

Link attempt with parts.. I click the "hotline for forums" icon to the right It says copied. I see either a url option or https option to paste. I pasted 4 photos, but when I click submit or save changes, they vanish and are no longer inside My reply post...

2025/06/16 23:25:09

<< ..10 11 12 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account