Latest Posts

Latest Posts (p.18)
Briggs & Stratton Forum
Martyj

Re: 1975 2hp vacujet

I pulled my pickup tube. Its plugged. Screen is probably shot. No jet in end...

2025/07/07 18:19:06
Small Engine Forum
doug2500

Re: Briggs 21 HP Single Cylinder. Bad rings?

Everything is working now. I found that a really weak belt can make it look like the blade engagement lever is working backwards. It's fine. Thanks for your help. Now I have another Briggs question. I pulled the 10HP engine off my sawmill since it hasn't been startable in about a year. I know the en..

2025/07/07 16:52:31
MTD Forum
grancpe

2004 Bolens rear deck spring

I made the mistake of removing the rear deck pin without realizing there was a spring on it. Spring shot out back and I cannot figure out where the other end goes. On end went around the pin. I also found a hook thing which is where I believe the other end went but the is no place to install it on t..

2025/07/07 15:33:24
Briggs & Stratton Forum
Martyj

Re: 1975 2hp vacujet

I only see a needle and seat on the side of the carburetor, The exploded view drawing does not show anything. Now if you are looking at the actual pickup tube picture, I believe that metal looking thing on the end of the tube is where it goes into the carb...

2025/07/07 11:57:10
SRTsFZ6

Re: 1975 2hp vacujet

https://www.partstree.com/parts/briggs-stratton-296476/ It's just pressed into the carb body and if you look close at the link/pic, there's apparently a very, very small jet in there(at the tip). That must be clear. Blowing by mouth, even if clear would be very difficultdue to it's tiny size. You ca..

2025/07/07 07:57:45
SRTsFZ6

Re: Briggs and Stratton 18hp V-TWIN motor# 350777-1137-E1

Part # 1011? https://www.partstree.com/models/350772-0045-01-briggs-stratton-vertical-engine/carburetor-1-5/ Pic's would help.. ...

2025/07/07 07:47:36
stony69jason

Briggs and Stratton 18hp V-TWIN motor# 350777-1137-E1

This motor is on John Deere GT235 lawnmower motor# 350777-1137-E1. I just bought it and this vacuum line wasn't hooked up, it's on front left side of carb (looking at it). Does anyone know where it goes ? Could you please tell me so I can hook it up properly. There is a second hole in the ai..
5
2025/07/09 07:09:22
stony69jason

Briggs and Stratton 18hp V-TWIN motor# 350777-1137-E1

This motor is on John Deere GT235 lawnmower motor# 350777-1137-E1. I just bought it and this vacuum line wasn't hooked up, it's on front left side of carb (looking at it). Does anyone know where it goes ? Could you please tell me so I can hook it up properly. There is a second hole in the ai..
11
2025/07/08 13:42:26
Martyj

Re: 1975 2hp vacujet

Yes we are talking about the pickup tube and It should be clear but does the throttle cut It out. Looks clear but i cant blow thru it. How Hard is the tube to replace. Mine looks like Its all plastic and really jambed into that hole. What year is that edger above?..

2025/07/06 20:00:57
SRTsFZ6

Re: 1975 2hp vacujet

Like my current edger (all original)? https://i.postimg.cc/SxcL1W67/DSCN1049.jpg..

2025/07/06 16:33:42

<< ..16 17 18 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account