Latest Posts

Latest Posts (p.17)
Lawn Mower Forum
SRTsFZ6

Re: 19hp Intek won’t start

Please post EVERYTHING you did... Also, did you check to see the flywheel key way is in the same position between bothflywheels? Did you check compression and / or valves going up and down under the valve cover? ...

2025/07/08 14:23:54
47plymouth

Re: 19hp Intek won’t start

Ya, I tried that with no luck, even bought a new carb and installed it, nothing so I reinstalled the old one back on, shutoff valve is new and I can feel it click when ignition is on, I’m stumped..

2025/07/08 14:18:52
SRTsFZ6

Re: 19hp Intek won’t start

Remove the air filter, squirt some carb cleaner or brake cleaner down the throat and try to start it. If it starts momentarily, you have a fueling issue and we'll go from there.. Advise.. ...

2025/07/08 14:16:20
47plymouth

19hp Intek won’t start

Hi, I have a 19hp intek motor in my craftsmanT1600 mower, I had a failure of the magnets on the flywheel so I bought a new one on eBay, I also installed a new coil and stator and spark plug, I have a good spark at the spark plug but I cannot get the engine to pop or fire even with starting fluid, I..
15
2025/07/09 07:13:51
SRTsFZ6

Re: 98902 1615 diaphram

Pic shows what goes where...: https://i.postimg.cc/QMb5tPhx/Capture.jpg..

2025/07/08 13:52:27
SRTsFZ6

Re: 98902 1615 diaphram

https://www.partstree.com/models/98902-1615-e2-briggs-stratton-vertical-engine/carburetor-fuel-supply-4/..

2025/07/08 13:51:45
Briggs & Stratton Forum
SRTsFZ6

Re: Briggs and Stratton 18hp V-TWIN motor# 350777-1137-E1

Is there an actual nipple on the carb, (between the throttle and block), or? Looking at the carb pic I posted earlier, there doesn't show anything. RARELY is there a vent tube in the carb- Sometimes in the area of the float bowlSHOULD the needle and seat leak, overflow fuel would EXIT the engine and..

2025/07/08 13:42:26
Small Engine Forum
SRTsFZ6

Re: Briggs 21 HP Single Cylinder. Bad rings?

You simply have rust on the crankshaft preventing the cover from coming off. Push the cover back on fully and with some sandpaper (maybe 120 grit), polish the shaft(especially close to the sump cover) until shiny steel. It'll come right off. A little lube on the shaft wouldn't hurt either. ...

2025/07/08 07:40:55
doug2500

Re: Briggs 21 HP Single Cylinder. Bad rings?

Sorry, I should have been more clear, it's not the starter cover, it's the sump cover on the block. Mod 20S232-1246F1..

2025/07/08 06:34:17
Lawn Mower Forum
oletrkguy

98902 1615 diaphram

I took the carburetor off the tank to clean the carburetor and change the diaphragm and gasket with hopes to stop it from shutting down soon after starting it. I noticed the gasket was against the tank and then the diaphragm and then the carburetor. My question is, is that correct? I googled for the..
3
2025/07/08 15:12:13

<< ..16 17 18 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account