Latest Posts

Latest Posts (p.8)
Briggs & Stratton Forum
SRTsFZ6

Re: Governor Adjustment for 20 HP B&S V2

So a single throttle cable, no separate second cable for the choke, correct? So with that said, (and I think you also mean), the throttle pulled back is idle.Pushed forward increases the speed, eventually to approx 3,600 RPMs (WOT). Pushing forward beyond that activates the choke (and WOT remains), ..

2025/02/18 08:15:20
ueww40

Re: Governor Adjustment for 20 HP B&S V2

Ok Scott. I was wrong. The wire link that goes to the choke does NOT have a loop. It has zig zags on both ends like Z. I have no problems understanding the adjustments between the governor shaft and lever. The confusion arises from the manual which indicates that the control swivel at WOT is also as..

2025/02/17 16:02:20
SRTsFZ6

Re: Governor Adjustment for 20 HP B&S V2

Hummm, interesting. It's possible they made a change in models and yours "fell" into the group as Briggs ran out /changed parts.. ...

2025/02/17 15:09:16
ueww40

Re: Governor Adjustment for 20 HP B&S V2

Thanks Scott. I will double check the choke linkage according to your previous post and get back shortly. Btw, the video was very good and explains it all very well. Remember, some time ago I asked if my engine (406777-0442-B1) had compression release and everybody said Yes. This time when I replace..

2025/02/17 12:11:53
John Deere Forum
Steverino

Re: Fuel Line Briggs Intek V-Twin

Not a bad idea Scott. Will be adding an inline fuel shutoff as well. Just need to determine the best location when the time comes...

2025/02/17 11:55:24
Briggs & Stratton Forum
SRTsFZ6

Re: Governor Adjustment for 20 HP B&S V2

Ok, the short ziggy zag part attaches to the carb choke plate (atop the carb) That elongated part does NOT "attach" solidly to anything.The elongated part SLIPS into the main bracket. Then part of the main linkage has a tab that PUSHES on the elongated part of the linkage. Any excess play (when acti..

2025/02/17 11:52:04
ueww40

Re: Governor Adjustment for 20 HP B&S V2

Does the link to the actual choke have like an "elongated loop"on one end and a short zig zag on the other (that would attach to the choke itself)? . Yes, it does. The loopy end attaches to the choke and the zig zaggy end attaches to the link that is connected to the control swivel..

2025/02/17 10:22:38
SRTsFZ6

Re: Governor Adjustment for 20 HP B&S V2

Does the link to the actual choke have like an "elongated loop"on one end and a short zig zag on the other (that would attach to the choke itself)? ...

2025/02/17 07:39:09
Tecumseh Forum
SRTsFZ6

Re: Spark Plug Question

The NGK plug is as good as the Champion.. "Plug n play" (pun intended)! ...

2025/02/17 07:35:05
Briggs & Stratton Forum
SRTsFZ6

Re: Governor Adjustment for 20 HP B&S V2

Loosen the bolt/nut for the governor arm. Hold the throttle (on the carb) to wide open throttle. A third hand may help with that. Now, the swivel that goes thru the block. Turn it in the same direction (till it stops) it would as the arm would normally push it. Lock down the bolt nut.. If you do it ..

2025/02/17 07:26:54

<< ..7 8 9 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account