Latest Posts

Latest Posts (p.23)
Kohler Engine Forum
SCdetector

CV-16s spark advance module

I have a Kohler Command CV-16s 43514 with the SAM module, my module recently went out and it would not advance the timing past idle. I bought the aftermarket market DSAI 12 584 12s unit off EBay for $20, the engine runs but pops going from idle to full throttle, to be expected for the price. I tried..
2
2025/06/07 22:23:00
Briggs & Stratton Forum
joegyoung

B&S 344cc engine sputters/dies after 20+ minutes

I have this on mower and it has been doing this for the last month. I have done several things like drain the carb bowl but no luck. Let it sit for 1+ hour and it starts right up and runs for 20+ minutes then dies. Seems like carburetor but any other ideas? Strange that it would take that long for t..
2
2025/06/07 14:51:41
Tecumseh Forum
a1parrothead

Re: Help Adjusting Governor Tecumseh H35

Thanks Scott. Time to tear apart the chipper! Jeff..

2025/06/07 09:45:35
Toro Forum
SRTsFZ6

Re: Toro ring deck needed

I don't see it available any where.. If your slightly mechanically inclined, I'd remove what's left, take it to a hefty vise and go at it with a 5 lb ball peen hammer... You'd be surprised how much you can straighten it out as it's not terribly thick..Take your time... ...

2025/06/07 07:01:39
Tecumseh Forum
SRTsFZ6

Re: Help Adjusting Governor Tecumseh H35

If it's adjusted properly and still over revving, there's no other tests I know ofW/O pulling the sump cover (or side cover) for a visual of the governor itself. A side cover gasket is cheap, to peek inside. I'd pick one up, then if the governor is needed, get that later.. ...

2025/06/07 06:46:22
Toro Forum
[email protected]

Toro ring deck needed

The part I need is a Toro 88-9780 which is a steel ring in several pieces that bolts to the deck. I hit a rock and mangled mine. It is discontinued and no where to be found. The mower is a 71182 12-32 XL Toro tractor. Thanks!..
5
2025/06/12 06:41:18
Tecumseh Forum
a1parrothead

Re: Help Adjusting Governor Tecumseh H35

Scott, Thank you. That spring that goes from the governor arm to under the carb somewhere is what seems to be keeping the governor arm pulled towards the carb and keeping the throttle wide open. With that said, if I take that spring off temporarily, so there is no external force pulling on the arm, ..

2025/06/06 21:44:56
SRTsFZ6

Re: Help Adjusting Governor Tecumseh H35

The direction the throttle would move for WOT, loosen the lock nut and turn the internal, (that goes into the engine) in the same directionas if it was opening the throttle. Then tighten the nut. If you do it the opposite way, the throttle won't open at all... And yes, with the engine off, the gover..

2025/06/06 21:01:32
a1parrothead

Help Adjusting Governor Tecumseh H35

I am working on a Troy Bilt Chipper with an H#% engine. When starting it revs full throttle, and yes, I know the governor could be shot, But, I want to make sure. This is a simple set-up with no throttle control lever to adjust engine speed. The carb is clean with all parts moving freely. When off t..
6
2025/06/09 17:22:59
Craftsman Forum
SRTsFZ6

Re: Craftsman t210 not starting

Sounds like that length of wire you replaced has a break under the insulation.. Glad you found it! ...

2025/06/06 17:12:31

<< ..22 23 24 .. - Powered by APG vNext Trial

© 2025 APG vNext Trial Version 5.5

Use My Existing Forum Account

Username: Password:

Use My Social Media Account